2001 Hyundai Accent GS Transmission Speed Sensor

2001 Hyundai Accent GS Transmission Speed Sensor - NOTE: Both pulse generator-B inspection and TCM reprogramming procedures should be performed. PULSE GENERATOR-B INSPECTION PROCEDURE: 1. Open and secure the hood. 2. Remove the resonator. 3. Locate the pulse generator under the battery tray.

Disconnect the pulse generator connector (blue) and remove the pulse generator male connector (black) from the bracket. 4. Using an ohmmeter, check the resistance between terminal No. 3 and No. 4 in the disconnected pulse generator male connector (black color). Resistance value: 215-275W (at 20°C or 68°F) If the resistance is lower or higher than the specification, replace the pulse generator (P/N 45955-22700). If the resistance is within specification go to Step 5. 5. Clean both ends of the disconnected pulse generator connectors with aerosol electrical contact cleaner.

6. Apply contact grease (P/N 00305-F0000-39, NYOGEL 760G), into all four terminal openings of the blue female connector until each terminal opening is completely filled with grease. 7. Reconnect the pulse generator connectors and reattach the connector to the bracket. Reinstall all removed components in the reverse order of removal. TCM SPECIFICATIONS CAUTIONS BEFORE REPROGRAMMING: 1. Conduct reprogramming with the ignition key in the “ON” position. 2. Be careful not to disconnect any cables connected to the vehicle or Hi-Scan Pro during reprogramming. 3. Do not start the engine or turn the ignition key off during reprogramming.

WARNING: If reprogramming is interrupted, the manual update procedure must be used. 4. When the reprogramming is completed, turn off the ignition key for 20 seconds before starting the engine. TCM REPROGRAMMING PROCEDURE: 1. Insert the 16 MB reprogramming card into the top slot of the Hi-Scan Pro.

Download : 2001 Hyundai Accent GS Transmission Speed Sensor

Read more »

2010-2011 Hyundai Elantra Touring BX2328

2010-2011 Hyundai Elantra Touring BX2328

Tools Required 8MM Socket Drill 10MM Socket Phillips Screwdriver 14MM Socket Utility Knife 7/16″ Socket/Wrench Pliers 9/16″ Socket/Wrench Tape Measure 3/4″ Socket/Wrench 1 1/4″ Hole Saw Large Vise Grip 13/32″ Drill Bit Needle Nose Pliers 5/16″ Drill Bit Reciprocating Saw 17/32″ Drill Bit
Installation Instructions: 1. Using a Phillips screw driver, remove fi ve plastic pus pins from the top front of the fascia. Set pins aside to be reinstalled later. Do this to both sides of the vehicle. 2. Using a 10MM socket, remove two metric bolts from the air intake housing.

Set bolts aside to be reinstalled later. 3. Using a 8MM socket or a Phillips screwdriver, remove one screw just forward of the front tire, on the wheel well. Do this to both sides of the vehicle. Set screws aside to be reinstalled later. 4. Using a 10MM socket, remove fi ve metric bolts from the belly pan underneath the vehicle. Set belly pan and bolts aside to be reinstalled later. 5. Using a Phillips screwdriver, remove three plastic Phillips pushpins from just forward of the front tire along the bottom edge of fascia. The fascia is then ready to be removed from the vehicle by pulling fascia ends out to the side to release and then pulling it forward.

Do this to both sides of the vehicle. Set fascia and pushpins aside carefully to be reinstalled later. 6. On the passenger side moving from top right clockwise, remove the wire clips from the top tab to release the wires. Using a 10MM socket remove two metric bolts, one on each side. Use a Phillips screw driver to loosen the screw on the top left. Disconnect all wires and hoses, plug the hoses. Set the washer reservoir and bolts aside to be reinstalled later. 7. Relocate the ground wires, as shown in 7A to 7B. Using a 5/16″ drill bit drill a hole, attach the ground wires with a 1/4-20 x 3/4″ bolt and a 1/4-20 whiz nut on the back. Do this to both sides of the vehicle.

8. Using a utility knife, remove plastic guard by fi rst cutting fl ush with the bottom of the bumper. Do this to both sides of the vehicle. 9. Using a 10MM socket, remove the bolt holding the plastic guard in place. Do this to both sides then remove the guard. 10. On the driver’s side, unfasten the two clips holding the wire. Move the wire out of the way as trimming will need to be done to the frame.
Download : 2010-2011 Hyundai Elantra Touring BX2328

Read more »

2010-2011 Hyundai Elantra Touring BX2328 Manual Installation Instructions

2010-2011 Hyundai Elantra Touring BX2328 Manual Installation Instructions - Tools Required 8MM Socket Drill 10MM Socket Phillips Screwdriver 14MM Socket Utility Knife 7/16″ Socket/Wrench Pliers 9/16″ Socket/Wrench Tape Measure 3/4″ Socket/Wrench 1 1/4″ Hole Saw Large Vise Grip 13/32″ Drill Bit Needle Nose Pliers 5/16″ Drill Bit Reciprocating Saw 17/32″ Drill Bit
Installation Instructions: 1. Using a Phillips screw driver, remove fi ve plastic pus pins from the top front of the fascia. Set pins aside to be reinstalled later. Do this to both sides of the vehicle. 2. Using a 10MM socket, remove two metric bolts from the air intake housing. Set bolts aside to be reinstalled later. 3. Using a 8MM socket or a Phillips screwdriver, remove one screw just forward of the front tire, on the wheel well. Do this to both sides of the vehicle. Set screws aside to be reinstalled later. 4. Using a 10MM socket, remove fi ve metric bolts from the belly pan underneath the vehicle. Set belly pan and bolts aside to be reinstalled later.

5. Using a Phillips screwdriver, remove three plastic Phillips pushpins from just forward of the front tire along the bottom edge of fascia. The fascia is then ready to be removed from the vehicle by pulling fascia ends out to the side to release and then pulling it forward. Do this to both sides of the vehicle. Set fascia and pushpins aside carefully to be reinstalled later. 6. On the passenger side moving from top right clockwise, remove the wire clips from the top tab to release the wires. Using a 10MM socket remove two metric bolts, one on each side. Use a Phillips screw driver to loosen the screw on the top left. Disconnect all wires and hoses, plug the hoses. Set the washer reservoir and bolts aside to be reinstalled later.

7. Relocate the ground wires, as shown in 7A to 7B. Using a 5/16″ drill bit drill a hole, attach the ground wires with a 1/4-20 x 3/4″ bolt and a 1/4-20 whiz nut on the back. Do this to both sides of the vehicle. 8. Using a utility knife, remove plastic guard by fi rst cutting fl ush with the bottom of the bumper. Do this to both sides of the vehicle. 9. Using a 10MM socket, remove the bolt holding the plastic guard in place. Do this to both sides then remove the guard. 10. On the driver’s side, unfasten the two clips holding the wire. Move the wire out of the way as trimming will need to be done to the frame.
Download : 2010-2011 Hyundai Elantra Touring BX2328 Manual Installation Instructions

Read more »